Vinyal flooring install

Plan to stagger rows so that end joints do not fall at the same point for adjacent rows. Manufacturers recommend that end seams be offset at least 6 inches from row to row. For ease of installation, it is always best to remove the trim that makes contact with the floor. This includes baseboards, base shoe moldings, and case moldings around doors.

Often, removing doors from their hinges helps with installation, too. Door case molding is relatively easy to remove and replace, and doing this makes for an easier, cleaner installation.

If you do not wish to remove door trim or if you have protrusions that cannot be removed, you can cut the vinyl flooring to fit around these obstacles. Trim molding is typically attached with thin brad-like nails, and it can be removed by carefully prying it off with a flat pry bar.

To remove the brads from the trim, pull them straight through the molding from the backside, using pliers. If the trim is still in good shape after removal, set it aside for re-installation after the floor has been installed. Vinyl plank flooring can usually be laid right over existing flooring, but if there are any high spots, they should be sanded down to create a flush surface for the new floor. Your goal is to create the flattest, smoothest surface possible as the underlayment for the vinyl plank flooring.

Test fit the first row of vinyl planks down the length of the wall. Visually, the flooring layout will be most pleasing if cut planks are of roughly equal lengths at the opposite side walls. Start with a full plank at the center of the wall, and work to either side, so that cut planks at the ends will be of equal length. Cutting vinyl planks to size is similar to how drywall panels are cut. First, use a carpenter's square and utility knife to score partially through the face of the plank.

Run the knife lightly across the face of the plank several times rather than trying to cut it in one pass.

Vinyl planks are slippery, so be very careful when pulling back on the blade. Alternatively, you can use a fine-tooth handsaw to cut straight through the entire plank. Vinyl Tile What is Vinyl Tile?

Browse by color Gray Beige White Brown. Inspiration Design a Room. See all Vinyl Tile. Close Vinyl Tile Menu. Share Share. Download F Installation Guide for Contractors. Before You Buy. Know your installation options. Traditional fiberglass-backed and composite stone-backed products — You can choose a modified loose lay or a full-spread adhesive, and the adhesive can either be permanent or releasable.

Felt-backed products — These usually require a permanent full-spread adhesive, though select products can be perimeter bonded. Consider any installation challenges. Create an accurate budget. Decide whether to DIY or bring in a Professional.

Hiring a Pro? Find the best one for the job. Read the installation instructions. Prepare the room. Prepare the subfloor. Gather additional materials and tools. Acclimate flooring according to instructions, if necessary. During Installation. Many companies make vinyl plank flooring. Some specialize in vinyl floors of all types, while others make a wider range of floor products, including vinyl. Each brand has its own costs, colors, patterns, and other attributes to consider.

Below are some of the most popular brands for vinyl plank flooring and the average costs for their materials fully installed. Mohawk makes a very wide range of mid-grade vinyl flooring, including some vinyl planks. Their planks can be click-lock, peel-and-stick, or glue-down. The most common thickness is around 12 mil, but their floors are considered fairly durable and very low maintenance.

They have a range of warranties on their floors, depending on the line. Flooret is a unique manufacturer among other vinyl plank floors. They also have exceptional warranties on their material, which is extremely durable and long-lasting. Flooret has some of the longest warranties in the industry. Their floors are eligible for LEED credits, so when looking for a sustainable floor that is also low-cost and durable, Flooret is a good choice. NuCore has one of the widest selections of vinyl floor products on the market.

They offer more than styles and colors to choose from, making it easy for you to find the right fit for your home. They also strive to produce a quality material at a lower cost. This means they often have somewhat thicker and more durable flooring offerings at lower costs than competitors with the same quality floors. Shaw is one of the biggest floor producers today.

They make a very wide range of different vinyl products, including several types of vinyl planks. These include lines of both click-lock and glue-down options. Their material is usually a little thicker and better quality than most other companies, so their costs are higher.

COREtec is considered one of the most premium brands of vinyl floors. Many of their floors use a cork backing. This makes their vinyl planks thicker and more comfortable underfoot. This means their material is more expensive, and installation is more costly. Most of their floors are installed in a floating style, but some can be glued down. The lowest cost of installation is peel-and-stick, depending on the material thickness.

Click-lock installations are slightly more time-consuming than peel-and-stick and are a more expensive material. Glue-down installations tend to be more expensive for labor because the material must be rolled after it is put down. This takes additional labor and time. However, the glue-down material is usually less expensive, so the cost of the labor and material tends to even out between click-lock and glue-down once the material is installed.

The material is the easiest to install and the lowest cost in general. This material is so easy to install that many homeowners choose it for DIY installation. It is not quite as long-lasting as a glue-down installation but can be used on more uneven floors than a floating installation.

Peel-and-stick vinyl plank floors are less common than the other types, so you will have fewer options to choose from. This is also known as a tongue-and-groove or floating floor.

Floating vinyl planks do not adhere directly to the subfloor 2. Instead, they click together along their edges. This installation requires the subfloor to be perfectly smooth and flat, taking a little more time than a peel-and-stick floor installation. The planks are also usually thicker and more rigid to make the installation easier. This makes the installation and material costs higher than peel-and-stick.

This material is usually a little thinner and more flexible than click-lock. So while the installation is slightly harder and more expensive, the material is less costly.

Glue-down vinyl floors are not easy to DIY. They require a heavy metal roller to go over the floors after installation. Once down, these floors are very hard to get back up. Get free estimates from trusted vinyl plank flooring installation companies near me Get Free Estimates.

Vinyl plank flooring is fairly low maintenance. It does not require any special cleaners or waxing. Some types may scratch, so do not drag furniture across them. The material is not affected by moisture or water, so it can be installed in damp areas. Sweep or vacuum it regularly to remove debris that may scratch it.

Mop as needed to remove surface stains. Vinyl is non-porous and does not absorb moisture, so it is unlikely to permanently stain. Vinyl plank flooring is a tough, durable material that can be used anywhere in the home. It can be installed in wet areas like basements and bathrooms without consequences. Vinyl typically comes in 12 inch square tiles, but it may come in sheets. If you have vinyl sheets, all you have to do is cut it out to fit the room, allowing for seams if the room is wider than the sheet.

Vinyl tiles, on the other hand, must be applied in a pattern. Determine how you will lay the floor. You may strike a chalk line as a guide to the first row of vinyl if you are using tiles. Keep in mind that you will always start your pattern in the center of the room and work your way out, in order to keep it symmetrical.

Determine the application process for your vinyl. There are two types of vinyl: self-stick, and glue down. Self-stick vinyl is very straight forward, as it comes with an adhesive backing that you use to stick it to the floor. Glue down vinyl takes a bit more work, as it requires you to put a layer of vinyl flooring glue on the underlayer prior to placing your vinyl.

If you have self-stick vinyl, simply follow the directions for application and you are set. If you have unglued vinyl, continue on for instructions on applying it. Mark your pattern on your paper template.

To make applying your vinyl easier, you can lay it out and cut it to fit using your paper template. Simply lay the vinyl out on the template, and use it as a pattern for cutting your vinyl to size. Begin gluing the vinyl flooring. Get your vinyl flooring adhesive out, and get a notched trowel. Start in a corner of the room following your pattern , and scoop out some of the glue onto the trowel.

Always have a damp rag at the ready for spills or smears on the vinyl. Lay the vinyl. For solid vinyl tiles VCT, or vinyl composition tiles , place each one flat, perfectly aligned with the row, and snugly abutting the previous tile. Do not slide the tiles when laying them, as this will "drag" the adhesive. Press the vinyl down to stick it to the adhesive.

Apply pressure as you roll over the tile in order to stick it to the adhesive and the underlayer. Continue applying the vinyl. Work your way across the floor, applying the vinyl according your your pattern. Lay out some of the glue, allow it to dry until tacky, stick the vinyl, roll over it with your roller, and repeat the process at the next section. Fill the entire floor with the vinyl, until you reach the edges.

If you need to cut vinyl to fit the odd edge spaces, do so now. Otherwise, place your cut vinyl into these spaces and roll over them to verify that they are secured. Finish the flooring. If you installed your vinyl flooring in a bathroom, use a caulk gun to caulk around the edges of the floor where they meet with the baseboards.

This will protect from water damage and help your vinyl to last longer. Get matching vinyl transition pieces that fit flat against the flooring and the carpeting. Not Helpful 1 Helpful 7.

Sweep the concrete clean, apply adhesive with a trowel, and set the vinyl immediately. The glue will stay tacky for a while. Not Helpful 0 Helpful 6.